Ghost Wire 2.0, Super Flat Adhesive Wire, 16 AWG, White

$57.95
SKU SW-32985-50
Conductors
Length

Sign up for a restock notification!


Related Products:
See Also:

Make speaker wires disappear right on the wall or under the carpet with Sewell Adhesive Speaker Wire. This super-flat speaker wire can be used on almost any flat surface.

This super-flat speaker wire can be used on almost any flat surface. Perfect for running stereo signals across rooms, around corners, in automobiles, under flooring, or any situation where wires cannot be run through walls.

White backing allows wires to be simply attached and left uncovered, or it can be easily covered with paint, spackle, or flooring making the wire virtually invisible.

For an even cleaner install, we recommend using the Ghost Wire Terminal Block to connect the Ghost Wire to your regular speaker wire.

How to Terminate Ghost Wire

  1. Peel back the white backing about 1” and cut it off, exposing the adhesive and conductors
  2. Trim away white covering in between and at the edges of the conductors
  3. Remove the white covering from the opposite side of the conductor. It does not have adhesive between it and the conductor and should leave a nice clean copper surface when removed
  4. Fold the conductors 2-4 times, keeping the clean copper surface outwards
  5. Insert the conductors into the Terminal Block and tighten the set screws
  6. Insert your standard speaker cable in the other end of the terminal block and tighten the set screw.

(See videos tab for demonstration) 

How to Remove Bubbles from Ghost Wire

  1. Install the ghost wire onto a clean surface, pulling it tight as you do.
  2. Use a heat gun on low or hair dryer on high to heat the area where bubbles appear
  3. Smooth out the bubbles by rubbing back and forth over them. Use a glove if the heat is uncomfortable.

(See videos tab for demonstration) 

Running Ghost Wire Around Corners

We’ve had a lot of people ask us how to 90° turns when running it along the floor.

Here’s how:

  1. Run the cable along the edge of the wall with the adhesive side facing down
  2. Fold the cable back so the copper strips are facing up
  3. Fold the cable back down at a 45° angle, making a 90° turn

(See videos tab for demonstration) 

Tips and Tricks

For even more Ghost Wire tips and tricks, check out the Ghost Wire installation guide.

Videos

How to Terminate Ghost Wire

  1. Peel back the white backing about 1” and cut it off, exposing the adhesive and conductors
  2. Trim away white covering in between and at the edges of the conductors
  3. Remove the white covering from the opposite side of the conductor. It does not have adhesive between it and the conductor and should leave a nice clean copper surface when removed
  4. Fold the conductors 2-4 times, keeping the clean copper surface outwards
  5. Insert the conductors into the Terminal Block and tighten the set screws
  6. Insert your standard speaker cable in the other end of the terminal block and tighten the set screw.

How to Remove Bubbles from Ghost Wire

  1. Install the ghost wire onto a clean surface, pulling it tight as you do.
  2. Use a heat gun on low or hair dryer on high to heat the area where bubbles appear
  3. Smooth out the bubbles by rubbing back and forth over them. Use a glove if the heat is uncomfortable 

Running Ghost Wire Around Corners

We’ve had a lot of people ask us how to 90° turns when running it along the floor.

Here’s how:

  1. Run the cable along the edge of the wall with the adhesive side facing down
  2. Fold the cable back so the copper strips are facing up
  3. Fold the cable back down at a 45° angle, making a 90° turn

Ghost Wire Installation

Specifications

Mfg. Part Number

  • SW-32985-25 25 ft. 2 Conductor 
  • SW-32985-50 50 ft. 2 Conductor 
  • SW-32985-100 100 ft. 2 Conductor
  • SW-32986-25 25 ft. 4 Conductor 
  • SW-32986-50 50 ft. 4 Conductor 
  • SW-32986-100 100 ft. 4 Conductor

Brand

  • Ghost Wire™ by Sewell

Specifications

  • .375" Width (each conductor)
  • .5 mm thick (includes peel back layer, adhesive, and conductors)
  • 16 AWG
  • Pure Copper
  • 2 Conductor or 4 Conductor 
  • White Jacket
  • Rated up to 10 Amps
  • Indoor/Outdoor Use

Applications

  • Home Theater Surround Sound Speaker Wiring
  • Low Voltage Stage Lighting
  • 12 Volt Cabinet Lighting
  • Security Access Control Wiring

Customer Reviews

Based on 9 reviews
56%
(5)
22%
(2)
22%
(2)
0%
(0)
0%
(0)
A
A.P.
Cable works, mixed results with hiding the cable

I just installed a 25 foot run of this cabling and it works well! However, I personally thought the taper on the edges of this tape was not enough to sufficiently make this product disappear with just paint (I was installing at eye level under a light though, not at a baseboard). I applied two layers of drywall mud to feather out the edges and that worked fairly well, but one annoying issue was a slight separation/crack along the edge of the tape and mud feathering, even after two passes. Priming and painting kinda covered it, but the crack still shows a bit in a places. Overall it did the job for me, but it was more hassle than I was hoping for.

D
D.P.
$ Conductor Wire

This is really good but needs a little more sticky. It took two days pressing it several times to make it stick to the ceiling of the trailer.even after cleaning the ceiling first.

A
A.
Part Number: SW-32985-25
Very handy

Pros: Nice and thin, easy to placeCons: no 14 AWG version for longer runs, could use bevelled or feathered edges for easier blending when paintingOther:

A
A.
Part Number: SW-32986-50
Very nice idea for those difficult areas

Pros: Cons: Other: This product was a perfect find for a tough spot to add surround sound to the livingroom. Lays flat against the wall so it becomes somewhat hidden once painted. Worked very well for me. Would recommend to friends and family.

J
J.C.
Part Number: SW-32985-25
Wall wired

Pros: Easy to use.Cons: Tends to stand out on flat surfaces. Connectors are much bulkier than required, a solderable or compression connection could be better.Other: If the edges of the tape were "feathered", the tape would blend into flat surfaces much better.

You recently viewed

Clear recently viewed

Net Orders Checkout

Item Price Qty Total
Subtotal $0.00
Shipping
Total

Shipping Address

Shipping Methods