The Sewell InjectIR extends the signal from your remote controls (for Blu-Rays, DVRs, set-top boxes, etc.) by sending the remote control's IR (infrared) signal over your HDTV's existing HDMI cable.
NOTE: If the InjectIR Pro is not working and you have checked that the receiver and transmitter are on the correct ends, make sure the CECIR switches on both InjectIR units are switched to IR (push both switches towards the blue Sewell logo).
What is an IR extender?
With an IR extender cable, you can use your remote controller's functions without pointing it directly at the TV. This gives you more range and versatility in controlling devices.
How do you use an IR extender?
Connect the IR cable to the back of your TV and position the emitter near what you want control. Select OK on both devices, then choose "Extend" from one device's menu settings.
When you install your HDTV on a wall, or when you wish to hide your video source devices in another room or closet, you break the line-of-site view of your video devices that the remote controls rely on. This requires you to get an IR extender that can route your remote's IR signal directly to your source devices
Sewell's InjectIR is probably the most reliable and most easy-to-install solution on the market. Unlike other wired solutions, you don't have to run an additional cable through the wall, you can use the existing HDMI line.
How This Works
The Sewell InjectIR uses the unused CEC channel of your HDMI cable run to send the IR signal through it (CEC channel is used only for certain HDTVs that can send control commands to your video sources, so if you use CEC, you don't need to extend your remote controls). The unit has a switch that allows you to switch between IR injection and CEC channel use.
60 Second Install
Installing the Sewell InjectIR only takes a minute and doesn't require any drilling or cutting into your walls. Simply connect the transmitting unit directly into your HDTV's HDMI port, and then reconnect your HDTV's HDMI cable into the transmitting unit's female HDMI port. The transmitting unit has a port that accepts the included IR sensor. Place this included sensor somewhere near the TV where you will be aiming all of your remote controls.
Next, you plug the receiver unit directly into your video source's HDMI port. The receiver unit has a port for the included IR emitter which you point at your video source's remote control sensor. There is nothing more to do to set this up.
To sum up, the remote control signal from your remote hits the included IR sensor, the IR signal then travels into the transmitter unit and is injected into your HDMI cable. On the other end of the cable, the receiver unit picks up the signal and outputs it through the included IR emitter which is facing your video equipment's IR sensor. You will get perfect control of your devices every time.
Note: This product does not work with an HDMI Splitter.
- This product is NOT compatible with the following models of the AT&T U-verse cable box:
- Cisco Explorer 4642HDC, IPN 4320, IPN 330HD and the Motorola VIP series. As well as regional providers using the Cisco ISB7150/7105. There are other models of the U-verse that are also likely incompatible with the InjectIR.
- HDMI Female to Male Adapter
- Dual Band
- Will work with dual band devices
- With IR plug
- 33khz - 60khz Band (Dual Band Emitter)
- 480i, 480p, 720p, 1080i, 1080p, 4K
- HDMI 2.0
- Gold Plated
- Accurate and reliable reproduction of digital video signal, with no signal attenuation or distortion
- Transport both audio and video signals
- HDCP 2.2 Compliant
- Utilizes built in CEC channel
- Fully molded and compact size
- RX/TX cables are 5 feet long
- 1 - IR Receiver
- 1 - IR Emitter
- 2 - HDMI Adapter
- 1 - QuickStart Guide
We're sorry our product isn't working for you! Feel free to reach out to our customer service department to set up a return if you haven't already.
Works great, and an extremely easy set up!!
Worked perfect. Plugged it in and started using it. Really didn’t want hassle of programming an RF remote. I had already ran the hdmi cable to the other room with the cable box…and didn’t want to run another cable…so this was the perfect solution
Easy to install, clear directions, and works with our Spectrum remote. Allows us to keep cable box in cupboard and still use remote.
Works exactly as expected .. i am a repeat customer and came back based on previous good experiences.