Control all of your home theater video sources (Blu-Ray player, Cable box, TiVo, and anything else that uses a standard IR remote control) from behind walls or closets by extending the IR signal with this kit.
How this works
This kit comes with an IR Receiver, and an IR Emitter. Simply point your remote control at the Receiver, and it will send the signal wirelessly to the Emitter which will then transmit that signal to the devices you wish to control.
This kit can be combined with other BlastIR Wireless Kits to create custom setups.
It supports up to 10 "zones" with independent sending/receiving frequencies. (kind of like different channels on a walkie-talkie). You can change the zone by using a very small rotating switch located at the bottom of the receiver and emitter pucks. The Receivers will only communicate with the Emitters that are set to the same zone.
There are multiple ways to use the BlastIR Wireless PRO. Some setup examples are: One to one, All to All, One to Many, or Many to One. You can also purchase extra Emitters, or Receivers individually if you don't need an extra full pair.
One to One
All to All
One to Many
Many to One
Extend Reach with IR Emitter and Receiver Cable (Optional)
You can use the included Receiver and Emitter cables so further minimize what's seen on your setup. The emitter cable is a "Dual-headed" Emitter so it allows you to control an additional two devices. Magnetic Feet and Adhesive pads are also included to mount the BlastIR Wireless out of sight when using the IR Receiver and Emitter Cables.
If you already have a BlastIR Wireless PRO and need help setting it up, watch this video or check out the troubleshooting tips below. Also, feel free to call us at (800) 709-1345 and we'll help you set it up over the phone.
Is it receiving power?
Make sure the unit is plugged in completely and receiving power. Once the power cord is plugged in, the light should briefly turn blue when the device turns on, then turn blank, turning back on only when it receives a remote signal.Are the units too far apart?
The intended range between units is around 600 feet and should work around walls and through closed doorways, though the more obstacles there are, the more limited this range becomes.Is each device in the proper spot?
The receiver (blue-ringed device) should be next to the TV (or where you want to send the signal from). The emitter (orange-ringed device) should be next to the cable box or the device you want to control.Are you using the proper cord for each device?
You will want to make sure that the ring of color on the cord and device match in color.Are you receiving a signal?
If the device is not turning blue when you point the remote at it and press a button, it is not receiving a signal.
Here are a few things to check:
- Are you pointing the remote at the receiver?
- Does the remote have fresh batteries?
- Is only one device turning blue?
- Are both devices turning blue, but nothing is happening?
- The following devices are known to be incompatible.
- Yamaha HTR 6140
- Arris DCX 3520E-M
- OSD ATM-7 Speaker Selector device
Make sure that the device you are trying to send a signal to is the receiver (blue-ringed device).
Replacing the Batteries can increase the remote signal strength to help the repeater to have a stronger signal to send.
Make sure both of the units are on the same channel. The dial on the bottom side of the device should point towards a number. Changing the number changes the channel they are operating on. This number should be the same on both devices.
Try using the Emitter cable included with the package. It is teardrop-shaped and has two heads; you may have to try a couple of times, but finding the IR eye of your device and placing one of the heads in front of it can greatly boost reliability.
The device is to have a blue signal only when it receives a signal from your remote. If it is constantly blue, that means it is receiving interference from a nearby device. The most common culprit for this has proven to be a Mesh network. If it is turning blue constantly, distancing it from nearby devices, and changing the channel the BlastIR units are operating can be helpful.
See how your feedback has improved this product
7/28/17 Increased compatibility with Dish and Cisco boxes
Many people use the BlastIR Wireless with their current cable box. Every time we hear a report about a cable box (or any other device) not working with the BlastIR Wireless, we get to work on making the device compatible. This update helps those with a Dish or Cisco box.
6/1/18 Increased compatibility with Explorer, Spectrum, and Samsung boxes
Further widening the range of compatibility of the BlastIR Wireless. This update helps those with Explorer, Spectrum, or Samsung boxes.
6/1/18 Increased font size in manual
We found that the text size in the manual was simply too small. It has been enlarged throughout the manual to better use the space and make it easier to read.
8/30/18 Included magnet feet
With the release of our new Magnet Feet, we have decided to include two in every BlastIR Wireless box. A magnet foot is simply an adhesive rubber "dot" with a magnet embedded inside. After placed on the bottom of the BlastIR Wireless "puck" you can place it on metal surfaces such as the back of your TV or the TV mount itself. This could also keep the unit in place in your equipment cabinet or rack. We have also included a page in the manual to describe this.
- SW-32988 Kit
- SW-32988-RX Receiver Only
- SW-32988-TX Emitter Only
- SW-32988-X Transceiver
- Wireless Distance: 200m (650 ft.), distance may vary due to obstacles
- IR Receiver Distance: 7m (30 ft.)
- IR Frequency: 20-60Khz
- RF Frequency: 915 Mhz
- Wirelessly communicates in the 915-917 MHz band
- Power: 5V/0.5A
- Optional Cables Included: 3 ft. receiver cable and 10 foot. dual head emitter cable
- Blu-Ray Players (Sony, LG, Samsung, Panasonic, Yamaha)
- Cable and DVR Boxes (U-Verse, Dish VIP, Fios, Xfinity, DirecTV, Motorola, Cisco, Optimum, TIVO)
- AV Receivers (Denon, Sony, Onkyo, Yamaha, Samsung, Bose, LG, Marantz)
- Logitech Harmony Hub and Universal Remotes
- Anything else that requires an IR signal! If your device does not work, let us know which device and we will pay for any return shipping
- Yamaha HTR 6140
- Arris DCX 3520E-M
- OSD ATM-7 Speaker Selector
Each unit comes with the appropriate IR cables, power supply, and mounting accessories.
DownloadsBlastIR Wireless PRO Manual.pdf
Product didn’t work. Emailed to get return info and no one has reached out. Poor product, poor service= poor experience. Maybe this review will get someone to reach out???
Hello, we are sorry to hear that you are having issues with your unit. We would be happy to troubleshoot it with you or set up a return if needed.
We've attempted to email you a few times, but they don't seem to be getting through. You may want to check your spam/junk folder. If you would like, you can request a callback, here.
I needed a wireless device to allow me place to my cable box out of sight and still have the ability to change TV channels. I got this from the Blast Repeater. I contacted support with my wants/details and Sewell was very responsive. I made the purchase, and everything is working. Set up was easy and includes multiple ways to mount the devices. I am very pleased so far.
Great small adapter to change TV that is in a different room that works
Recently had a cabinet built to hide all my A/V equipment behind closed doors. With the receiver extension discreetly placed on the back wall beneath the TV and the emitter and extensions placed below I am able to seamlessly control my cable box, A/V receiver and dvd player. Installation took all of
works great, tv upstairs and cable box is downstaires